Do not run logic input wiring together with power cables; The instrument needs 150 ms to recognize a contact status variation; Logic inputs are NOT isolated by the measuring input. Yokogawa Electric Corporation - TC10-L - ENGINEERING MANUAL - PAG. The 3-year warranty extends 36 months after shipment from our factory. Notes: 1. When using an external power supply with 2-wire wiring of TC10, what is the input resistance when inputting 4-20 mA? Note: This filter will affect the measured value but also the control action the analogue retransmission and the alarms, Overall dimensions (L x H x D): 48 x 48 x 73 mm, This instrument is intended for permanent installation, for indoor. user must refer to the Engineering manual for special instructions. WARNING! requirements of the area in which the instrument is being installed. If this instrument is used in a manner not specified in this manual. There is no parameter for specifying the output direction. To change these parameters you need to enter the Conguration mode. terminal 1 and 2 to transmitter signal output. This is a list of recorder and controller products that support the New Legislative Framework (NLF.). Clamp meters use wide jaws that clamp around the outside of an electrical conductor to provide non-contact current measurements. Also, YOKOGAWA Electric Corporation assumes no liability for the customer's, failure to comply with these requirements. condensation); 5. and General Specification: GS 05C01E81-11EN. The UT75A also support open networks such as Ethernet communication. exposed terminals and wiring on the back. IM 05C01E81-01EN 1 Edition Oct. 2014 st Yokogawa Electric Corporation 2-9-32 Nakacho, Musashino-shi, Tokyo 180-8750 Japan internet site: www.yokogawa.com/ns Declaration of conformity and Manual retrieval TC10 is a panel mounting, Class II instrument. all phases of operation, service and repair of this instrument. The TC10-L supports easy configuration for a quick start-up, and it is configurable as a high limit or low limit controller. For measurements performed in the building instal-, For measurements performed at the source of the, - Wiring work must be carried out by a person with basic electrical, - Be sure to turn OFF the power supply to the controller before wiring, to avoid an electric shock. Notes: 1. The factory default password for conguration parameters is equal to 30. There are no water or other uids (i.e. Installation altitude: less than 2000 m; The instrument can be mounted on panel with a maximum, When the maximum front protection (IP65) is desired, the optional, - 0 to 12 V SSR Drive Output (OP4) connecting, - 12 Vdc (20 mA) transmitter power supply, connecting the 2 wire transmitter between, terminals 4 and 1; for 3 wire transmitter connect, terminal 4 to transmitter power supply input and. Input impedance:> 1 M. 1 digit @ 25C of room temperature; Electromagnetic compatibility and safety requirements. 3. Safety, Protection, and Modification of the Product, - In order to protect the system controlled by this product and the, product itself, and to ensure safe operation, observe the safety, precautions described in the Engineering manual. It has been designed The TC10-L supports easy configuration for a quick start-up, and it is configurable as a high limit or low limit controller. and workmanship for 18 months from the date of manufacturing. terminal 1 and 2 to transmitter signal output. To protect the AL2 and AL3 thresholds against, undesired changes, they are available only at "Parameters, list" level (password: 20). countries or regions where wiring will be installed. The output relay is always de-energized (opened) at poweron,even if PV does not exceed SP(A). Copyright 1994-2023 Yokogawa Corporation of America, {{ baseCtrl.fullNavList[baseCtrl.fullNavList[baseCtrl.currentMenuDepth].parent].name }}, {{ baseCtrl.fullNavList[baseCtrl.currentMenuDepth].name }}, Floating Production Storage & Offloading (FPSO), Special Solutions of OpreX Transformation, Terminal Logistics Suite VP (Terminal Automation), Visual MESA Supply Chain Scheduling (VM-SCS), Cloud Inventory Management Solutions (Web*VMI), Platform for Advanced Control and Estimation (Advanced Process Control), OpreX Laboratory Information Management System, Remote Plant Performance Operation and Remote Consulting (KBC Co-Pilot Program), Mobile Field Device Management (FieldMate), Predictive Maintenance of Pump Cavitation, Advanced Analytical Instrument Management System (AMADAS), FluidCom Chemical Injection Flow Controller, Real-time Plant Data Sharing Service (Web*Technician), OpreX Data Model Broker / Design Data Validation, OpreX IT/OT Security Operations Center (SOC), Plant Information Management System (Exaquantum), Alarm Reporting and Analytics (Exaquantum/ARA), Integrated Production Information (Exaquantum/mPower), Power Performance Calculations (Exaquantum/PPC), Safety Function Monitoring (Exaquantum/SFM), Operator Trending Module (Exaquantum/OTM), Remote Data Synchronization (Exaquantum/RDS), Synchronous OPC DA Manager (Exaquantum/SDM), Manufacturing Data Exchange (Exaquantum/MDX), Public announcement of Yokogawas products, Distributed Fiber Optic Temperature Sensor, Industry and Interface Libraries (Applications and Interfaces), Yokogawa Pre-Engineered Analyzer Solutions - YES, Loading, Metering and Blending Automation, Plant Annunciator and SOE Recording System, Transmitterless SENCOMSMART Sensor Platform, Advanced Control Bioreactor System BR1000, Yokogawa announcement to Windows XP users regarding Systems products, A Business Value Decision ofImpact and Significance, Yokogawa Cloud IT/OT Connectors & Integrations, TC10-L Temperature Controller Limit Control Type Engineering Manual, TC10-L Temperature Controller Limit Control Type Serial communicaiton protocol, TC10-L Temperature Controller (Limit Control Type), Model TC10-L Temperature Controller (Limit Control Type). )The state of output relay is energized (closed) and the output (OUT) display lamp turns off if the PV does not exceed SP at power-on. voltage contact between terminals 4 and 16; - 0 to 12 V SSR Drive Output (OP4) connecting, - 12 Vdc (20 mA) transmitter power supply, connecting the 2 wire transmitter between, terminals 4 and 1; for 3 wire transmitter connect, terminal 4 to transmitter power supply input and. of use, service life and misuse are not covered by this warranty. The SP value is not displayed if you dont specify a control operation. Yokogawa Electric Corporation - TC10-L - ENGINEERING MANUAL - PAG. Model: digitalview ALR-1400, digitalview 417100041-3. 3. The relative humidity is in accordance with the instrument, The instrument can be mounted on panel with a maximum, When the maximum front protection (IP65) is desired, the optional, - Digital Input (DI2) connecting a free of. With thermocouple K input, can I display digits after the decimal point for the temperature? 2. - For control relay output, alarm relay output, and power terminal, L H C o R o D o F /GK Temperature Controller, NOTE about the structure of this document, The usual installation sequence is the reverse of the operator, During installation, the first step is the wiring procedure followed, by the complete configuration. and General Specification: GS 05C01E81-01EN. It also includes a ladder sequence function. be downloaded (free of charge) from the web-site: The Authorised Representative for this product in the EEA is: Viale Indipendenza 56, 27029 Vigevano (PV) - ITALY, The following general safety precautions must be observed during. Can I use the DI function to switch between auto/manual and between run stop/start? TC10s compact design allows for a broad range of applications/uses while maintaining a high level of accuracy. For complete controller configuration see the Engineering Manual. 2.56 in min. What is the I/O response time of the TC10? Model: TC10 Digital Indicating Controller with one universal input, one control output, and one selectable I/O. Calibration: According to EN 60751/A2. of use, service life and misuse are not covered by this warranty. switch is a device for turning off the power to the instrument. We call this set conguration parameter set (or conguration parameters). (63% response when the input changes from 10% 90%). The UT32A-D is a compact digital indicating controller with selectable 2-loop control. Pt 1000 calibration: According to EN 60751/A2. . For different configurations, see, Wattmeter (instantaneous power expressed in kW) (note 1), Wattmeter (Power consuption expressed in kWh/h) (note 2), Absolute worked time (expressed in days) (note 3), Absolute worked time (expressed in hours) (note 3), Notes: 1. Safety, Protection, and Modification of the Product, - In order to protect the system controlled by this product and the, product itself, and to ensure safe operation, observe the safety, precautions described in the Engineering manual. Sometime, e.g. Copyright 1994-2023 Yokogawa Electric Corporation. The EU Declaration of Conformity and the manual of the controller. Note: The complete list of the default parameters is available in Appendix A. all phases of operation, service and repair of this instrument. This manual is intended for the following personnel: - Engineers responsible for installation, wiring, and maintenance of, - Personnel responsible for normal daily operation of the, Calls attention to actions or conditions that could cause serious or, fatal injury to the user or damage to the instrument, and indicates, precautions that should be taken to prevent such occurrences. TC10-L is a panel mounting, Class II instrument. Nadcap AMS2750F - What's New and How to Comply? Select a mounting location having the following characteristics: 2. Are the TC10s wiring terminals screw terminals? Select a mounting location having the following characteristics: 2.There is minimum vibrations and no impact; 4.There are no water or other uids (i.e. The equipment wholly protected by double insulation or, - Whenever a failure or a malfunction of the device may cause dan-, gerous situations for persons, things or animals, please remember, that the plant must be equipped with additional devices which, - We warrant that the products will be free from defects in material. 1. The Yokogawa TC10-L limit controller is an FM-approved limit controller that can be configured either as a high limit or as a low limit controller by a user. When the upper display is showing a group and the lower display is blank, this key allows to enter in the selected group. Controller YOKOGAWA . If the other instruments have an SG terminal, how should I wire it? Such, applications include nuclear power equipment, devices using, radioactivity, railway facilities, aviation equipment, air navigation. At this point you can set the operator. all phases of operation, service and repair of this instrument. 4.Pay attention to the line resistance; a high line resistance may cause measurement errors. Use a tester or similar device to ensure. IM 05C01E81-01EN, 2-9-32 Nakacho, Musashino-shi, Tokyo 180-8750 Japan, EU Declaration of conformity and Manual retrieval, TC10 is a panel mounting, Class II instrument.